VCL-SafeCommTM,
16 E1 Links (48 E1 Ports)
(1+1 Automatic Protection Switch)
Product Overview
The VCL-SafeComm,
16 E1
Links (48 E1 Ports), 1+1 Automatic Protection Switching Equipment
may be used to protect upto 16 E1 Links (48 E1 Ports), point-to-point
links and provide an alternate communication route to each E1 Link
between any two E1 points.
In the event of the failure of the primary (Main) E1
communication route, the VCL-SafeComm 16 E1 Links
(1+1 Automatic Protection Switching Equipment) automatically
switches the E1 traffic to a secondary (standby) E1 route. The
VCL-SafeComm, 16 E1, 1+1 Automatic Protection Switching equipment is
available in a 2U high chassis which may be mounted in any DIN
standard,19-Inch rack. |
|
This product allows the user to design 1+1
(protected) redundant E1 routes on similar (fiber-fiber), or
complementing (fiber-radio) transmission mediums.
The criterion for switching between the primary
(main) and the secondary (protected / standby) routes is user
programmable. Criterion for switching between the primary (main) and
the secondary (protected/standby) routes may be Loss-Of-Signal on E1
links, or AIS (All-Ones AIS alarm) condition. The criterion for
switching time and recovery time between the primary (main) and the
secondary (protected / standby) routes is user programmable.
Data transported on the E1 Links is transparent and
protocol independent.
Features & Highlights
- High density protection switching equipment (upto 16 E1 Links
i.e. 48 E1 Ports)
- To provide an independent point-to-point, protected E1 Link
between two "E1 USER PORTS" on similar (example fiber-fiber), or
dissimilar (fiber-radio) mediums
- To provide 1+1 E1 redundancy support to higher order
multiplexers e.g. E2, E3
- System configuration and management interface through "CLI"
text based commands
- Transport A-bis Interface on redundant E1 links
- Provide 1+1 Protection Routing / Path between BSC and BTS
- These ensure that mission critical voice, data, control and
management traffic are properly supported and maintained even
during E1 backhaul facility outages. When the primary (working)
link fails, the E1 traffic is automatically switched to the
standby (secondary) link to ensure maximum uptime.
- Through the comprehensive remote configuration and alarm
management capabilities of the VCL-SafeComm, 16 E1, 1+1 Automatic
Protection Switching Equipment the product may be used to improve
network reliability and control
- Traffic Protection
- Alternate Facility Advantages
- Service Differentiation Agreements
- Increased Network Reliability Resilience
- Media and Path Diversity
- Remote Management
- Alarm logging and monitoring.
|
|
Benefits
- Customer Relations
- Competitive
- Service Level
- Back-haul Network
- Technology Migration
- User Programmable 1+1 Protection Parameters:
- Loss of
Signal
- AIS (All Ones
Alarm)
Technical Specifications
E1 Interface
|
Number of Interfaces
|
Total 48 E1
interfaces
16 for Main E1
Links
16 for Primary E1 Links
16 for Secondary E1 Links |
|
Line Rate |
E1 - 2.048 Mbps |
|
Line Code |
HDB3 |
|
Frame Structure |
G.704 |
|
Bit Rate |
2048 Kbps ± 50 ppm |
|
Jitter Tolerance |
As per ITU-T G.823 |
|
Output Jitter |
< 0.05 UI (in the frequency range of 20 Hz to 100 Khz) |
|
Pulse Mask |
As per ITU (CCITT) Rec. G.703 |
|
Conformity (electrical) |
G.703 |
|
Nominal Impedance |
120 Ohms, balanced |
|
Applications
Providing 1+1 alternate paths between any two
Transmissions mediums (active+standby). e.g:
- Fiber / Fiber
- Radio / Fiber
- Radio / HDSL
- Fiber / HDSL etc.
Applications Diagram
Technical specifications are subject to change without
notice.
All brand names and trademarks are the property of their respective owners.
|
